まず停止
温度、ハードウェア、エネルギー伝達、STOP ボタン関連では、無理な再スキャンを繰り返さないでください。
ULTHERAPY PRIME
Ultherapy エラーコード案内
機器担当者が不具合を記録し修理相談できるよう、一般的な Ultherapy メッセージコード、原因、初期確認を整理しています。
点検相談を送信
コードを記録
画面を撮影し、コード、トランスデューサ型番、残ライン数、発生手順を記録してください。
アクセサリを確認
ハンドピース、トランスデューサ、USB、通風、接触部が主な初期確認ポイントです。
メッセージコード
一般的な Ultherapy メッセージコード
初期参考用であり、メーカー IFU、ユーザーマニュアル、現場点検の代替ではありません。エラーが繰り返す場合は使用を停止し点検を依頼してください。
| Code | 箇所 | 考えられる意味 | 初期確認 |
|---|---|---|---|
| B | Handpiece | Internal handpiece temperature is too high. | Pause use and let the handpiece cool down; check for long continuous operation or poor ventilation. |
| C | Control Unit | The control unit detected a hardware event and stopped. | Restart as instructed on screen; if it repeats, record the code and arrange inspection. |
| E | Communication | Communication halted during initialization. | Restart the system and confirm the boot process completes; avoid power loss or removing accessories mid-process. |
| G | Control Unit | The control unit detected a hardware event and stopped. | Restart and observe whether it recurs; keep context and photos if it does. |
| H | Transducer | Transducer motion was not detected. | Stop scanning first, then remove and reinsert the transducer; confirm it is latched into the handpiece. |
| I | Communication | The control unit detected a communication event. | Restart and observe; if accompanied by handpiece or transducer issues, record accessory status. |
| J | Handpiece | Handpiece communication halted. | Restart and check whether the handpiece cable and port are secure. |
| K | Software | Software halted due to an event. | Restart the system; if it persists, avoid repeated attempts and arrange inspection. |
| L | Transducer | The transducer has no remaining lines. | Replace the transducer before continuing; record the model and remaining-line status. |
| M | Handpiece | Handpiece motion halted. | Check that the handpiece and transducer are correctly installed and locked; reinstall and test again. |
| N | USB | USB drive connection or read/write issue. | Confirm USB format, free space, and insertion status; do not remove it during system read/write. |
| P | Control Unit | The control unit detected a hardware event and stopped. | Restart; if it persists, record the code and arrange hardware inspection. |
| S | Emergency Stop | The red STOP button was pressed. | Confirm STOP button status, rule out accidental press, then restart as instructed. |
| T | Transducer | Internal transducer temperature is too high. | Pause use and let the transducer cool; use another transducer if needed. |
| U | Control Unit | Internal control unit temperature is too high. | Check ambient temperature and ventilation; let the main unit cool before testing again. |
| V | Energy Delivery | Energy delivery halted, possibly due to excessive reflected power. | Resume scanning as instructed; if it repeats, try another transducer and arrange inspection. |
| W | Transducer | The transducer is unauthorized or not accepted by the system. | Replace with a transducer suitable for the device; do not force continued operation. |
| X | Transducer | The system cannot read the transducer. | Remove and reinsert the transducer; check that the contact area is clean and dry. |
TRANSDUCER CHECK
トランスデューサエラーは接触部とロック状態を優先確認
H, L, M, T, V, W, and X are often related to the transducer, handpiece, or energy delivery. Photograph the contact surface, handpiece latch, remaining lines, and screen code before submitting for inspection.
THERMAGE FLX MANUAL NOTES
Thermage FLX 記録・確認ポイント
- When a Thermage FLX system error appears, record the code and screen message first, then follow on-screen instructions.
- If the activation button does not respond, confirm the handpiece is connected and the footswitch has not taken over activation control.
- If the touchscreen does not accept touches, press the center of the button and check whether the screen is locked.
- If the return pad heats up, stop operation and check pad placement and cable connection before continuing.
- If the handpiece overheats abnormally or the device has visible physical damage, stop use and arrange professional inspection.
REFERENCE IMAGES
元のエラーコード資料画像
手動確認用に元画像を残しています。通常は上の HTML 表をご利用ください。
Summaries reference user-provided Ultherapy Prime Instructions for Use System Messages and Thermage FLX System User Manual Troubleshooting / Error Codes / Maintenance sections. This page is for initial checks and repair communication only.